Duo Ceiling Lift
2 Way
A 2 way
only is powered up
and down and a assistant
would be required to push
the patient along the rail
where as a 4 way is powered both up & down and
side to side. |
|
 |
|
Duo Ceiling Lift
4 Way
A 2 way
only is powered up
and down and a assistant
would be required to push
the patient along the rail
where as a 4 way is powered both up & down and
side to side. |
|
 |
|
BHM Turn
Table
This is a track
changer allowing you to switch track from one
direction to the other. A 45 Degree Changer
will turn 45 degree and stop. A 90
Degree Changer will turn 90 degrees
and stop. |
|
 |
|
76
Meter Tracks
The 76 meter tracks
must be supported by a bracket every 36 inches and has
should only be used with the Voyager 420, The V4, The
Portable Voyager, The V3 or The Griffin.
All track sections include
all required bracket's, End Stop's, Trolley's, Track
Brackets and hardware required to install them. |
|
 |
|
144
Meter Tracks
The 144 meter tracks
can span a 19.6 Ft distance with only support on each
end. Use with the Voyager 420, 550, 800, V-3, V-4,
The Portable and the Griffin.
All track sections include
all required bracket's, End Stop's, Trolley's, Track
Bracket's and hardware required to install them. |
|
 |
|
30 Degree
Curve
All track sections include
all required bracket's, spacers, washers and hardware
required to install them. |
|
 |
|
45
Degree Curve
All track sections include
all required bracket's, spacers, washers and hardware
required to install them.
|
|
 |
|
70 Degree
Curve
All track sections include
all required bracket's, spacers, washers and hardware
required to install them. |
|
 |
|
90
Degree Curve
All track sections include
all required bracket's, spacers, washers and hardware
required to install them.
|
|
 |
|
Pivoting Wall
Bracket
The Pivoting Wall Bracket
allows you to support the
rail from a wall instead of the ceiling. This Bracket
requires
wall modifications as it is
meant to be bolted to two
2 X 4 studs. |
|
 |
|
Wall Post &
Bracket
The Wall Post Bracket allows
you to support the rail from a wall instead of the
ceiling. This
post extends to the floor
providing little strain on the
wall and bearing most of the weight or support from
the floor. |
|
 |
|
End Stop
The End Stop is used at the
end of a rail run to cap off
and secure the end to stop
the lift when it reaches the
end.
|
|
 |
|
End Rail
Charger
The End Rail Charger serves
to uses. 1st it serves as a
End Stop 2nd it serves as
a automatic charger for the
lift. (Please Note) that you
automatically receive one of
these with the purchase of
your lift. |
|
 |
|
Standard
Track Bracket
The Standard Track Bracket
is used to support rail to the ceiling. They are
secured to the ceiling using a 3" Inch lag
bolt. (Please Note) that you
automatically receive all the
brackets you will require with each section of rail
ordered
above. |
|
 |
|
Long Track
Bracket
The Long Track Bracket
is used to connect two rails together. This bracket is
not
an absolute requirement. Many installations are done
using only stand brackets. |
|
 |
|
Cathedral
Bracket
The Cathedral Bracket
is used for slanted ceilings. Additional brackets or
support may be needed with this type
of application. |
|
 |
|
Visible
Lateral Brace
The Visible Lateral Brace is
used to support the rail by picking up support from 0
to 90 degree angle off a wall
or the ceiling. |
|
 |
|
Adjustable
Lateral Brace
The
Adjustable Lateral Brace is used to support the rail
by picking up support from a 0
to 90 degree angle off a wall
or the ceiling. |
|
 |
|
Track
Junction
The Track
Junction is used to
connect support (3) track's at (1) point this is used
with the
Portable Voyager or (2) Standard Voyager Lifts. The
only other time this bracket is used is when you
simply want to use a section of rail to pick up
support 90 degrees to the side. |
|
 |
|
Joint Kit
The Joint Kit is used to add
support to the joining of two
rails however is not required and offers more of a
cosmetic service. |
|
 |
|
Long Joint
Kit
The Long Joint
Kit is used to add support to the joining of two rails
as is the standard joint kit however the long kit
gives added support to the joining of the two rails.
Again is not required. |
|
 |
|
Reverse
Bracket
The Reverse
Bracket with Joint Kit Is used when you are using a
turn. The turning rail can be used to go in ether
direction yet
the teeth change direction depending on the end that
is used to attach to. This bracket can be replaced by
simply using two standard brackets at the union. |
|
 |
|
X-Y System
The X-Y Gate is used to join one
track to ride on two other tracks, giving a lift the
full virtual range of the square the
tracks cover. This application is mostly found in
hospitals or medical facility as they service many
different size patients. |
|
 |
|
1/4 Shim
The 1/4 Shim is used to space
brackets as nearly all ceilings are not perfectly flat
or flush. |
|
 |
|
1/8 Shim
The 1/8 Shim is used to space
brackets as nearly all ceilings are not perfectly flat
or flush.
|
|
 |